A microscopy study of hyphal growth of Penicillium rubens on gypsum under dynamic humidity conditions

Summary To remediate indoor fungal growth, understanding the moisture relations of common indoor fungi is crucial. Indoor moisture conditions are commonly quantified by the relative humidity (RH). RH is a major determinant of the availability of water in porous indoor surfaces that fungi grow on. The influence of steady‐state RH on growth is well understood. Typically, however, the indoor RH constantly changes so that fungi have to endure frequent periods of alternating low and high RH. Knowledge of how common indoor fungi survive and are affected by the low‐RH periods is limited. In particular, the specific effects of a drop in RH on the growth of the mycelium remain unclear. In this work, video microscopy was used to monitor hyphal growth of Penicillium rubens on gypsum substrates under controlled dynamic humidity conditions. The effect of a single period of low RH (RH = 50–90%) interrupting favourable conditions (RH = 97%) was tested. It was found that hyphal tips ceased to extend when exposed to any tested decrease in RH. However, new hyphal growth always emerges, seemingly from the old mycelium, suggesting that this indoor fungus does not rely only on conidia to survive the humidity patterns considered. These findings are a fundamental step in unravelling the effect of RH on indoor fungal growth.


Introduction
Indoor moulds may excrete metabolites or fungal particles that induce allergic reactions or asthma in some subpopulations (Miller, 1992;Flannigan, 2001;Green et al., 2011). Furthermore, mould discolours indoor surfaces. To avoid such medical or aesthetical problems, strategies for the remediation of indoor fungal growth are required. A detailed knowledge of the conditions leading to mould colonization of indoor surfaces forms the basis for such strategies.
Fungal growth is influenced by many abiotic factors, such as moisture, temperature, nutrient availability, oxygen, chaotropicity (Cray et al., 2013) and pH. Of these factors, temperature and especially moisture are considered the most important factors influencing indoor fungal growth (Grant et al., 1989;Adan et al., 2011). Most indoor surfaces consist of porous materials, which can absorb and store the water required for fungal growth. While indoor water can originate from leakage or flooding, the adsorption of water vapour from air with sufficiently high relative humidity (RH) onto a porous material can result in fungal colonization of surfaces (Coppock and Cookson, 1951;Clarke et al., 1999;Bekker et al., 2015). Several studies on the effects of moisture on indoor fungal growth have, therefore, focused on the dependence of growth on porous materials on the RH (e.g. Grant et al., 1989;Pasanen et al., 1992b;Adan, 1994;Chang et al., 1995;Viitanen and Bjurman, 1995;Chang and Foarde, 1996;Clarke et al., 1999;Viitanen et al., 2010;Johansson et al., 2013;Bekker, 2014;Bekker et al., 2015;van Laarhoven et al., 2015).
The minimal moisture requirements of a fungus are generally expressed in terms of the water activity (a w ) of its environment (Scott, 1957). Fungal protoplasm has its own a w , and water transport occurs from high to low a w . Water uptake, which is crucial for cell processes and structure (Griffin, 1981;Magan, 2007), can therefore occur only when the internal a w is below the a w of the environment. RH and a w are related: both are expressions of water's chemical potential, in the vapour and condensed phase respectively (Atkins and de Paula, 2006). Therefore, when an indoor substrate and ambient RH are in equilibrium, the RH defines the substrate a w via a w = RH/100%. The influence of a decreasing steady-state a w or RH on growth has been extensively investigated on agar media (e.g. Ayerst, 1969;Magan and Lacey, 1984;Judet et al., 2008;Nanguy et al., 2010;Ponizovskaya et al., 2011) and on various building materials (e.g. Grant et al., 1989;Pasanen et al., 1992b;Nielsen et al., 2004;Viitanen et al., 2010). While the exact relationship depends on the fungal species and substrate material, a general trend of slower germination and hyphal growth with lowered a w or RH has been found, down to a system-specific critical value, below which no growth occurs (Stevenson et al., 2015).
Typically, the indoor RH is not constant, but rather fluctuates due to indoor temperature gradients and due to household activities such as cooking or bathing. While the indoor humidity is below the RH threshold for mould growth on average, it has been shown that these transient periods of high RH are sufficient for sustaining mould growth on indoor surfaces (Pasanen et al., 1992a;Adan, 1994;Viitanen et al., 2010;Johansson et al., 2013;Johansson, 2014). A full picture of indoor fungal growth, therefore, needs to include detailed knowledge of how the fungi survive and respond to the recurring periods of low RH that interrupt the humidity conditions suitable for growth.
Several authors have studied the effect of transient humidity on fungal growth on various building materials, such as gypsum (Adan, 1994;Bekker, 2014), wood (Viitanen, 1997;Johansson et al., 2013) or concrete (Viitanen and Ojanen, 2007). These workers each performed growth experiments in which fungi on porous substrates were exposed to a cyclic regime of alternating periods of high and low RH. Because the tested materials, moisture regimes and fungal species varied per study, direct comparison of these studies is difficult (Vereecken and Roels, 2012;Dedesko and Siegel, 2015). In general, however, each of these researchers found that exposure to a cyclic RH lowers the rate of fungal proliferation during the periods of high RH as compared with proliferation during the same RH at steady-state conditions. Bekker (2014) focused on the effects of a single period of low RH on the growth of Penicillium rubens on gypsum substrates. She found that low RH periods with different characteristics, such as duration and moment of application, influence growth differently. Moreover, Bekker's results indicate that mycelium remains viable during short periods of low RH (< 48 h), whereas regrowth on substrates exposed to longer periods of low RH seemed to originate only from conidia that germinated post-desiccation. A limited number of studies on agar have reported similar phenomena (Diem, 1971;Luard, 1982;Park, 1982;Browning et al., 2008;Bekker, 2014). For growth on porous materials, however, a sound interpretation is hindered by the lack of direct microscopic data. The studies so far have used macroscopic methods to quantify growth, that is, methods based on measurement of macroscopic properties of fungal colonies as a whole. An important method used in many previous studies is the assessment of surface coverage with either stereoscopy (Adan, 1994;Viitanen et al., 2010;Johansson, 2014) or digital images (Nielsen et al., 2004;Bekker, 2014). As such, the effects of transient humidity conditions on the individual stages of fungal growth, that is, germination, hyphal growth or sporulation, remain unclear.
The aim of this work was to explore how hyphal extension on porous materials is influenced by a single period of low RH. Video microscopy experiments (van Laarhoven et al., 2015) are reported in which hyphal growth of the indoor mould P. rubens (Andersen et al., 2011;Samson, 2011) on gypsum, a common porous building material, was recorded during and after its exposure to low RH. Knowledge of the hyphal response to RH changes will produce a more complete understanding of indoor fungal growth and will aid the interpretation of macroscopic studies on indoor fungal moisture relations. Ultimately, this may lay the foundations for new control strategies for indoor fungal growth.

Gypsum substrates
The substrates for the growth experiments were made by mixing gypsum ((Ca 2 SO 4 ) 2 ÁH 2 O, Sigma Aldrich, St. Louis, Missouri, United States) with an aqueous solution of Czapek Dox Borth (Oxoid, 8.76 g l À1 ) and the trace metals ZnSO 4 Á7H 2 O (2.5 9 10 À3 g l À1 ) and CuSO 4 Á5H 2 O (1.25 9 10 À3 g l À1 ). The solution was first autoclaved, then mixed with the calcium sulphate hemihydrate at a mass ratio of 2:3, and finally cast into 3 mm thick moulds. The samples were cured and dried for 48 h at room temperature in a Bio Safety Cabinet (BSC) (CleanAir, Class II -EF/B) to remove excess water.
The surface of each sample was coloured with a thin layer of Fe 3 O 4 (Metzger Black), to provide sufficient contrast for microscopy. The layer was applied by pipetting 5 ll of a Fe 3 O 4 suspension in water (33.3 g l À1 ) on to the substrate. The samples were then again stored in the BSC until the suspension water had evaporated. The resulting Fe 3 O 4 layer typically had a thickness of about 20 lm, as determined with a profilometer (confocal interferometer, Smart; Sensofar, Barcelona, Spain). Inspection with cryo-SEM showed that the layer was porous with typical pore sizes in the order of 0.1-1 lm (van Laarhoven et al., 2015).

Fungal strain, conidial suspension and inoculation
Penicillium rubens (strain CBS 401.92; CBS Fungal Biodiversity Centre, Utrecht, The Netherlands) was used as the test organism in this study. This strain was formerly known as Penicillium chrysogenum, but was reclassified in 2011 (Houbraken et al., 2011).
Stock conidial suspension was created as follows. Conidia were collected by wetting 1 week old P. rubens cultures on MEA with autoclaved, demineralized water with 0.05 vol% Tween80 and subsequently scraping the surface of the colonies. The resulting conidial suspension was filtered with sterile glass wool to remove mycelium fragments. The suspension was then pelleted three times by centrifugation, each time followed by washing with autoclaved demineralized water with 0.05 vol% Tween80. Finally, 30 vol% of sterile glycerol was added to the suspension. The final concentration of the stock was counted using a hemocytometer, being 1.6 9 10 8 ml À1 . The stock was subsequently stored at À30°C.
Gypsum substrates were inoculated with conidial suspension of P. rubens as follows. An amount of stock was unfrozen and diluted to a concentration of 10 6 ml À1 before use. The area on the substrate coloured with Fe 3 O 4 was then inoculated by pipetting 5 ll of spore suspension onto it. In this way, approximately 5000 spores were evenly distributed over an area of approximately 10 mm 2 . Inoculated samples were then dried in the BSC for about 20 min to evaporate the suspension water. Consequently, the occurrence of a non-equilibrium water distribution near the inoculum during experiments was prevented. An analytic balance (Mettler Toledo, Columbus, Ohio, United States) was used to confirm that at least 95% of the suspension water had evaporated before incubation of the samples.

Incubation and RH control
The inoculated samples were stored in small incubation chambers (Fig. 1). The RH inside these chambers was controlled with an aqueous glycerol solution of defined concentration and a w on the bottom of the container, below the samples (Forney and Brandl, 1992). An a wmeter (Labtouch-aw Basic, Novasina, Lachen, Switzerland) was used to verify the a w of the solutions with an accuracy of AE 0.01 (equivalent to AE 1% RH in the incubation chambers). Syringe pumps (NE-1600; New Era, Farmingdale, New York, United States of America) were used to replace one glycerol solution with another, thereby dynamically controlling the RH. The containers were airtight to prevent the development of inhomogeneous RH profiles and to prevent evaporation-induced changes in the concentration and a w of the glycerol solutions. Moreover, verification of the a w of solutions before and after experiments confirmed that their a w did not change noticeably during the experiments. The setups were kept in a constant temperature room and cameras were water cooled so that the setups had a uniform, constant temperature (23.3 AE 0.1°C), as verified with 4 thermocouples (NI USB-9213; National Instruments, Austin, Texas, United States) distributed across the incubation chamber. This again ensured that homogeneous RH profiles developed throughout the whole container after each change of glycerol solution.
Equilibration of the RH throughout the incubation chamber after each change of glycerol solutions was driven by vapour diffusion; no additional stirring was applied. This was done to keep hyphae on the surface unperturbed by moving air, making it possible to follow hyphal extension with video microscopy. A control measurement during a change of solutions from RH = 97% to RH = 97% indicated that hyphae indeed remained undisturbed by the mechanical process of changing solutions. To confirm that diffusion facilitated sufficiently fast equilibration of the chamber, the RH at the location of the sample was measured as a function of time with a RH sensor (SHT71; Sensirion, Staefa, Switzerland) after switching between glycerol solutions ( Fig. 2A). Equilibrium is reached within approximately 15 min and possibly faster, since the measurement is limited by the response time of the sensor (bold dashed line). The RH was also measured during cyclic replacement of two solutions for several periods to confirm that the same RH value was reached every time ( Fig. 2B).

Quantification of fungal growth on the gypsum substrates
During the experiments, samples were observed through the transparent lid of the container with a USB-microscope (Dino-Lite 7013MZT (AnMo Electronics Corporation, New Taipei City, Taiwan), numeric aperture 0.22, optical resolution~1.5 lm). A magnification of 4709 was used, corresponding to a field of view (FOV) of 0.84 mm 9 0.63 mm and a pixel size of 0.6 lm 9 0.6 lm. The contrast provided by the Fe 3 O 4 layer on the substrate allowed the observation of hyphal growth on the samples. It is stressed that germination and germ-tube formation could not be resolved: only developed hyphae growing above but parallel to the surface can be followed (van Laarhoven et al., 2015) The thickness of the microscope working plane was~75 lm, as determined with a micromanipulator (Leica micromanipulator, Leica Leitz, Wetzlar, Germany). Growth was monitored at 1 h intervals with time-lapse recording.
The recorded movies were post-processed to quantify the observed hyphal growth. A custom MATLAB script was used to trace the position of individual hyphal tips from series of frames like those shown in Fig. 3A. Hyphal length as a function of time, starting from the first sight of growth, could be determined accordingly. An example of such data is displayed in Fig. 4, which shows the length of 37 individual hyphae that were traced from two movies of a full measurement, plotted as a function of time with t = 0 the moment of inoculation. The dotted lines mark the period of low RH.
Based on the movies, three aspects of growth were quantified. First, the growth rate of each individual hypha was determined on the basis of a linear fit, as illustrated in Fig. 4A. Second, fitting of the hyphal length also allowed the identification of the first moment in time each hypha becomes visible in the FOV (shown by the arrow in Fig. 3A), that is, the point in time where the observed hyphal length in Fig. 4 is equal to 0. Third, for each movie, the moment of conidiation was defined as the timestamp of the last frame in which no conidiophores could be recognized in the FOV (shown by the arrow in Fig. 3C).

Growth experiments
The RH exposure of samples during growth experiments is illustrated in Fig. 1B. All samples were initially incubated at RH = 97%. After 96 h, samples were exposed to a lower RH of certain value RH min for a period with duration Dt (Fig. 1B). The RH was switched back to 97% at the end of the period of low RH.
To investigate the influence of RH min , a series of experiments was performed in which RH min was set at a fixed and constant value of 50%, 60%, 70%, 80% or 90%.
To investigate the influence of Dt, the measurement series described above was carried out twice, with Dt set to 24 h and 1 h respectively.
As a reference, growth at a steady-state RH = 97%, that is, uninterrupted by a period of low RH, was measured as well.
Unless otherwise noted, the period of low RH was initiated 96 h after incubation. However, during the 96 h of fungal growth at RH = 97% prior to the application of a low RH period, conidiophores bearing new conidia might already form in the more mature mycelium. To exclude the possible Directly after inoculation at t = 0, samples are stored at RH = 97% for 96 h. Then, samples are exposed to a period of lower RH with value RH min with duration Dt. The RH returns to 97% after the period of low RH, and the experiment continues until conidiation is observed on the sample. role of these newly formed conidia, additional measurements were performed in which a period of RH min = 50% or 90% and Dt = 24 h was applied 48 h after inoculation. After the period of low RH, recording of growth on the samples continued until conidiation was visible in the FOV. After that, a measurement was terminated because growth at that point was typically so advanced that hyphae overlapped extensively and could not be followed. Measurements were performed in triplicate for every combination of RH min and Dt.

Statistical analysis
The general trends in the growth rates as a function of RH min were investigated for experiments with both Dt = 24 h and Dt = 1 h. Since only trends were tested and no regression was attempted, RH min was treated as a categorical variable. Sample sizes were generally unequal and homogeneity of variances was not assumed, so a Welch's one-way ANOVA was used, followed by a Games-Howell post hoc analysis. All statistical analysis was performed in Microsoft Excel 2010. An alpha level of 0.05 was used for all statistical tests.
Linear fits of the length of hyphae as a function of time were performed with MATLAB.

Results
Main observations before, during and after application of a period of low RH   Fig. 3A. Growth rates measured during the initial 96 h of steadystate RH = 97% (Fig. 1) served as a reference point for each experiment, justified on the basis of comparison with the steady-state experiments. The average of these initial growth rates is included per experiment in Fig. 5. Welch's one-way ANOVA shows that the average initial growth rates are statistically heterogeneous (F 10,49 = 5, P = 2.9e-5). However, further analysis (Games-Howell post hoc tests, P = 0.05) showed that the average initial growth rate of any experiment did not differ significantly from the average growth rate during steady-state growth at RH = 97%, which was 8 AE 3 lm h À1 . The movies for which Dt = 24 h show that within an hour after initiation of the low RH period (Fig. 1), hypha cease growing and are suddenly displaced, as shown in Fig. 3B. Also, no new growing hyphae appeared during the low RH period. The sole exception to this occurred for RH min = 90% and Dt = 24 h. In that case, three hyphae continued to grow during the period of low RH at a low growth rate (0.7 AE 0.3 lm h À1 ), as shown in Fig. 4A.
In the case of Dt = 1 h, the period of low RH was too short to register whether hyphae were still growing during the period of low RH. However, hyphae growing before the low RH period could be seen to displace at the initiation of low RH and did not continue growing from that point onwards (See Fig. 4B). The only exceptions occurred in the cases of a RH min of 90% or 80%, where, respectively, five and two hyphae were observed to grow prior to and after the low RH period.
For every combination of RH min and Dt during experiments, hyphal growth eventually reinitiated on all samples after the RH was brought back to 97% (Fig. 1). It is stressed that hyphal tips that ceased growth during the low RH period did not resume growth: all hyphae that were seen to grow in the second period of RH = 97% (apart from the exceptions mentioned above) appeared as newly detected hyphae such as illustrated in Fig. 3A. The regrowth during the second period of RH = 97% was influenced by the characteristics of the low RH period, as will be discussed in the following sections.
Influence of a period of lower RH on subsequent hyphal growth rates Figure 5 shows the average hyphal growth rates before and after the low RH period as a function of RH min . For Dt = 24 h (Fig. 5A), the growth rate before and after the low RH period did not differ significantly for a RH min of 70%, 80% or 90%. The average growth rates after periods of RH min = 50% and RH min = 60%, however, are substantially higher than the rates before the low RH period (~8 AE 3 lm h À1 before and~30 AE 15 lm h À1 after).
For Dt = 1 h (Fig. 5B), the post-RH min growth rates are significantly higher than pre-RH min growth rates for each RH min . The response to a RH min of 50% or 60%, however, does not differ significantly from the other responses, as in the case for Dt = 24 h.
Influence of a period of lower RH on the moment of initiation of subsequent growth Figure 6A shows the moments in time at which individual hyphae became visible in the FOV, grouped per RH min . For Dt = 24 h (Fig. 6A) and a RH min of 80% or 90%, the first new hyphae become visible within an hour after the end of the low RH period and from then, gradually, more hyphae keep appearing. The appearance of the first new hyphae following a RH min of 70%, 60% or 50%, on the other hand, is delayed by 10, 20 or 40 h respectively. For Dt = 1 h (Fig. 6B), new growing hyphae become visible within 1 h after the end of the low RH period for all RH min and from then, gradually, more hyphae keep appearing (also see Fig. 4B).

Influence of a period of lower RH on subsequent conidiation
The times when conidiation was observed in each movie were collected and shown in Fig. 7A. The data are grouped by RH min and Dt; the moment of conidiation for growth at steady-state RH = 97% is included as well. Comparison of the average conidiation times for Dt = 24 h, Dt = 1 h and Dt = 0 h (steady-state) shows no significant difference between the cases of Dt = 1 h and Dt = 0 h, but also shows that conidiation is significantly delayed in the case of Dt = 24 h compared with both other cases (Welch's one-way ANOVA, F 2,10 = 32, P = 3.7e-5 and Games-Howell post hoc tests, P = 0.05).
Further statistical analysis to find a trend in conidiation times with RH min was not appropriate due to the small amount of data points per RH min , which was limited by the number of movies. It is important to note, however, that the delay in conidiation for all cases of Dt = 24 h was more than 48 h, that is, twice longer than Dt.

Regrowth after a low RH period applied 48 h after inoculation
The average growth rates of hyphae growing during the second period of RH = 97% after a period of Dt = 24 h, applied after 48 h since inoculation, were 8 AE 3 lm h À1 and 22 AE 4 lm h À1 for RH min = 90% and RH min = 50% respectively. Furthermore, new growing hyphae appeared immediately after the period of RH min = 90%, but was markedly delayed after the period of RH min = 50%, as is shown in Fig. 7B.

Hyphal response to a sudden decrease in RH
The main consequence of hyperosmotic shock to a fungus is an outflow of water that results in loss of turgor (Deacon, 2006). On agar, immediate loss of turgor in filamentous fungi has been shown to cause the hyphae to loose rigidity, shrink and curl up (Park, 1982;Deacon,  2006; Lew, 2011). This may explain the observed shifting of hyphae right after the initiation of the period of low RH, which essentially constitutes a hyperosmotic shock. The steady-state RH below which no growth occurs was previously determined to be~86% for specifically P. rubens on gypsum (Adan, 1994;van Laarhoven et al., 2015). This means hyphal growth could be expected during a period with RH min = 90% (Fig. 4A) but not during RH min ≤ 80%. It is noted that the hyphal growth rates observed here during RH min = 90% (0.7 AE 0.3 lm h À1 ) fall within the spread of hyphal growth rates previously observed for P. rubens on gypsum at steady-state RH = 90% (at steady-state RH = 90%, van Laarhoven et al., 2015). Still, even for RH min = 90%, only 2 out of 9 followed hyphae continued growing past the initiation of the low RH period. It is likely that the other hyphae lost turgor and therefore ceased growing. On agar, Luard (1982) observed that P. chrysogenum, a fungus very closely related and similar to P. rubens (Houbraken et al., 2011), took 8 h to regain turgor and resume growth after a decrease in a w from 0.99 to 0.95. After a decrease from 0.99 to 0.93 or lower, however, she observed no recovery of growth at all. This matches our observation that hyphae that cease growth do not recover during the 24 h period of RH = 90%.

Resumption of hyphal growth following rewetting after a period of low RH
Our results indicate that for any considered combination of Dt and RH min , the mycelium that developed prior to the period of low RH remains viable and produces new hyphae upon rewetting. We suggest this based on the following observations. First (A), following the end of all low RH periods with Dt = 1 h, several new growing hyphae appeared within an hour (Fig. 6B). The same occurred after periods of RH min ≥ 80% and Dt = 24 h (Fig. 6A). The fast appearance of these growing hyphae indicates that they originate from the previously developed mycelium.
Second (B), after periods of RH min ≤ 60% with Dt = 24 h, appearance of the first new hyphae was delayed for 20 h or more. However, regrowth occurred at a highly increased extension rate. The dramatically increased extension rate indicates a clear response to the low RH period. This suggests that this regrowth originates from structures that have retained some memory of the period of low RH, that is, the mycelium.
Based on the delayed conidiation after a period of low RH with Dt = 24 h (Fig. 7A), one might alternatively conclude that all regrowth in this case stems from previously ungerminated conidia rather than the old mycelium: a completely new colony has to develop before conidiation can occur. Such a response to a period of low RH was, for instance, previously suggested by Bekker (2014). It is stressed, however, that conidiation is also delayed in the cases of Dt = 24 h, RH min = 80% or 90%, which are cases where hyphal growth resumes immediately upon rewetting after the period of low RH. Thus, a delay in conidiation should not necessarily be equated to the unviability of the old mycelium.
Still, it is stressed that, apart from regrowth from the old mycelium, it is possible that previously ungerminated conidia might, eventually, germinate and contribute to regrowth following a period of low RH. This cannot be excluded, as the currently used methods could not detect conidia or germ-tube formation. Germination cannot, however, explain the immediate appearance of hyphae in case A. Further, it is unlikely that previously ungerminated conidia would respond to a period of low RH with an elevated growth rate like in case B, since their primary function is to withstand even more stressful moisture conditions (Griffin, 1994;Wyatt et al., 2013). Moreover, Bekker (2014) purposefully exposed ungerminated conidia of P. rubens on gypsum to similar moisture regimes and observed no differences in growth from those as compared with growth from conidia under a steady-state RH = 97%.
Apart from previously ungerminated conidia, newly formed conidia might also contribute to regrowth eventually. In the case of a low RH period being applied after 96 h of growth at RH = 97%, new conidia might have already formed, as shown by an SEM study of Bekker et al. (2012) who observed that conidiation of P. rubens on gypsum at RH = 97% could occur as early as 92 h after inoculation. The results shown in Fig. 7B, however, indicate that hyphal growth responds similarly to a low RH period applied at 48 h after inoculation as to one applied after 96 h. This suggests that possible newly formed conidia are not crucial to this response, as the response also occurs in their absence.
Summarizing, we therefore conclude that, for all RH treatments considered, it is plausible that the previously developed mycelium produces new hyphae. It should be noted that hyphal tips that cease growth at the start of a low RH period did not resume growth afterwards. Therefore, it is likely that the observed new hyphal growth stems from branching from the old mycelium, forming new tips. Luard (1982) similarly observed regrowth of P. chrysogenum colonies on agar via branching, which occurred 250 lm behind the leading edge of the colony, 2 h after a hypoosmotic shock from a w = 0.93 to a w = 0.98. This conclusion does not match the findings of Park (1982), who exposed P. chrysogenum on agar to a more severe 168 h desiccation period at RH~60%. He observed that 50 h after the desiccation, hyphal growth resumed from the centre of the colony, from which he concluded that the new growth stemmed from previously ungerminated conidia from the inoculum. The hyphal responses to desiccation reported here, however, cannot be explained with previously ungerminated conidia being the only source of regrowth after desiccation.

Increased hyphal growth rates after a period of low RH
The mechanism that led to the enhanced growth rate of hyphae that grew after all periods of duration Dt = 1 h and the periods of Dt = 24 h with RH min ≤ 60% is unclear and explanations are speculative. One possible explanation might be that the severe period of low RH destroy a large part of the previously developed mycelium. The contents of the destroyed mycelium might then provide additional resources for the few surviving hyphae.
Another explanation might be a modification of the substrate by the desiccation. When the porous gypsum is dried fast, it might result in transport of additional Czapek nutrients to the surface of the sample, as has previously been shown for the drying of aqueous solutions in porous media (e.g. Gupta, 2013). Additional steady-state growth experiments on samples pre-treated with a similar RH periods (data not shown), however, did not reveal a visible increase in growth rates.
Another possible explanation involves the fungus actively increasing its hyphal extension rate in response to the lower RH. It is known that fungi can direct their biomass increase by regulating the allocation of resources in a trade-off between hyphal branching and hyphal extension (e.g. Trinci, 1974;Prosser and Tough, 1991;Heaton et al., 2012). Typically, hyphal extension rate is favoured over branching frequency in stressful or nutritionally sparse conditions so that the fungus' foraging capabilities are increased. Such a reaction might have been triggered by the lower RH. This could not be confirmed with the method used here, as the quality of the images was unsuitable for the collection of data on branching and total biomass production.
Delay of conidiation after a long period of low RH Compared with growth on samples that were exposed to steady-state RH = 97%, conidiation was delayed by more than 48 h by a low RH period of Dt = 24 h, whereas Dt = 1 h did not delay conidiation significantly. To our knowledge, a common expectation is that water stress leads to earlier conidiation in fungi, although little literature is available on this subject (Abdel-Hadi and Magan, 2009;Duran et al., 2010). Our observation that conidiation of P. rubens on gypsum is delayed by a 24 h exposure to even mildly lower RH therefore does not match with this expectation. More research is needed to explain this mismatch. Insufficient data points were collected per RH min to perform a statistical test for trends with RH min , but it is stressed that conidiation is also delayed in the cases of Dt = 24 h, RH min = 80% or 90%, which are cases where hyphal growth resumes immediately upon rewetting after the period of low RH. The knowledge that conidiation may respond differently to moisture history than the progression of mycelial growth is important for the interpretation of experiments in which the assessment of growth depends on the visibility of conidia (e.g. Nielsen et al., 2004;Bekker, 2014). Bekker, for instance, performed growth experiments with P. rubens on gypsum in which she assessed substrate discolouration after desiccation. From a delay in conidiation after a severe desiccation (48 h, RH min = 15%), she concluded that regrowth originated only from previously ungerminated conidia. In contrast, the data on hyphal growth rates presented here indicate that part of the regrowth may stem from the previously established mycelium even while conidiation is delayed.

Concluding remarks
In conclusion, we have identified several ways in which a period of low RH influences hyphal growth of P. rubens on gypsum for the first time. First, growing tips exposed to a desiccation of any considered duration or RH become unviable for further growth afterwards. Second, however, growth of new hyphae will eventually occur. Third, at least part of these new hyphae originate from the mycelium that developed prior to the low RH period, which indicates that parts of the mycelium other than the tips remain viable during all moisture regimes considered. Fourth, a period of low RH can change the hyphal growth rates afterwards. Finally, both the moment of production of new hyphae and that of new conidia can be delayed by a period of low RH, which indicates that current fungal growth can be dependent on past moisture conditions. It is stressed that the evidence for regrowth from the old mycelium after a period of low RH is indirect, in the sense that it is inferred from the measured timescales that are involved with regrowth after the low RH period. The conclusions presented in this work could be strengthened by using stronger microscopy methods that are able to record branching of the mycelium directly, although this will not be trivial in the case of porous substrates.
A limitation of the methods used in this work is that they provide little information on the total fungal biomass produced as a function of time. In the future, such information in concert with the data on hyphal growth rates could be used to construct a more comprehensive picture of mycelial colonization rates of gypsum and other building materials. Data on biomass formation could be obtained from enhanced post-processing of the movie data, or from other macroscopic methods designed specifically for the task, such as ergosterol determination (Nielsen et al., 2004) or the assessment of thermal output (Wadso, 1997).
Future work should include using the methods presented here to gain further insight in the effects of desiccation of hyphal growth. More complex RH schemes could be used to investigate the effect of multiple desiccations on subsequent development, to support the work of previous authors on the effects of cyclic humidity conditions (Adan, 1994;Viitanen and Ojanen, 2007;Johansson et al., 2013). On the other hand, as previously mentioned, a desiccation actually consists of two consecutive shocks, so investigating the effects of these shocks separately with an even simpler RH scheme might prove valuable for obtaining a more structured insight in the fungal response to desiccation. The methods could also be used to test novel compounds or materials that inhibit growth of moulds on indoor surfaces under simulated real conditions. Another interesting extension of the current work might be to investigate the response of other species, which might respond to transient humidity conditions differently. Indeed, there are indications that phylloplane indoor species of the Cladosporium genus (Park, 1982;Segers et al., unpublished data) whitstand transient humidities better than Penicillium.